Tag Archive for: electrochemical quartz-crystal microbalance

Publication on AWSensors technology

Methods for Calibrating the Electrochemical Quartz Crystal Microbalance: Frequency to Mass and Compensation for Viscous Load

/in , , /by

Authors: Claes-Olof A. Olsson, Anna Neus Igual-Muñoz and Stefano Mischler

Journal: Chemosensors (2023)

 

Abstract

The main output from an Electrochemical Quartz Crystal Microbalance is a frequency shift. This note describes how to separate the mass- and viscous load contributions to this shift by a calibration procedure. The mass calibration is made by electroplating from a copper sulfate solution in ethanol/water with 100% current efficiency. An estimate of viscous load is obtained by measuring the energy dissipation and is related to frequency change using the Kanazawa–Gordon equation. Two approaches are discussed: either by performing calibration experiments in a series of water–glycerol mixtures or by following oscillations in frequency and dissipation by collecting data during the stabilization phase of the experiment.

 

You may read the full paper here.

Publication on AWSensors technology

Highly Ordered Graphene Polydopamine Composite Allowing Fast Motion of Cations: Toward a High-Performance Microsupercapacitor

/in , , /by

Authors: Adnane Bouzina, René Meng, Cyrille Bazin, Hubert Perrot, Ozlem Sel, Catherine Debiemme-Chouvy

Journal: Adv. Mater. Interfaces (2023)

 

Abstract

The simple and eco-friendly preparation of microsupercapacitor remains a great challenge. Here are presented the preparation and the characterizations of an all-solid symmetric micro-supercapacitor based on a new composite formed of highly ordered graphene sheets due to the presence of polydopamine between the layers, which present a d-spacing of 0.356 nm. This graphene-polydopamine composite is prepared by electroreduction of graphene oxide (GO) followed by the electrooxidation of dopamine added into the initial solution, i.e., after GO reduction. In Na2SO4 solution, this composite material shows excellent capacitance and stability even at a high scan rate (2 V s−1) and a very low relaxation time (τ0) of 62 ms. This value is in very good agreement with the high transfer kinetic and low transfer resistance values of the ions implied in the charge storage process (Na+·2H2O and Na+) determined by ac-electrogravimetry. Finally, it is shown that the all-solid micro-supercapacitor (interdigitated electrodes obtained using a CO2 laser and Na2SO4/PVA hydrogel) prepared with this new composite delivers a remarkable energy density of 6.36 mWh cm−3 for a power density of 0.22 W cm−3 and exhibits excellent cycling stability (98% of retention after 10 000 cycles at 2 V s−1).

 

You may read the full paper here.

Publication on AWSensors technology

Interface Properties of 2D Graphene–Polydopamine Composite Electrodes in Protic Ionic Liquid-Based Electrolytes Explored by Advanced Electrogravimetry

/in , , /by

Authors: Adnane Bouzina, Hubert Perrot, Catherine Debiemme-Chouvy, and Ozlem Sel

Journal: ACS Appl. Energy Mater. (2022)

 

Abstract

A fundamental understanding of the processes occurring at the electrode/electrolyte interfaces is of paramount importance to enhance the performance of energy storage devices. Addressing this issue requires suitable characterization tools, due to the complex nature of such interfaces. By means of electrochemical quartz crystal microbalance (EQCM) and its advanced mode, the so-called ac-electrogravimetry, herein, we report on the interfacial properties of two-dimensional (2D) graphene–polydopamine (ERGO-PDA) composite electrodes in diverse electrolyte compositions including a protic ionic liquid (PIL), pyrrolidinium hydrogen sulfate [Pyr+][HSO4–]. We have performed a comparative study in a [Pyr+][HSO4–]–water binary mixture in the absence and presence of Na2SO4 and compared it with the interfacial behavior of ERGO-PDA in a 0.5 M Na2SO4 (pH = 2) pristine electrolyte. Our EQCM and ac-electrogravimetric analyses reveal that the [Pyr+] ions, due to their chaotropic nature, inhibit the approach of kosmotropic Na+ ions and water molecules to the interface, suppressing the contribution of electrodragged water molecules, substantially observed in the case of pristine aqueous electrolyte. Despite the dissimilarity of the charge compensation process occurring in the presence of [Pyr+][HSO4–], the ERGO-PDA electrode is able to maintain similar cycling stability (99% for 10,000 cycles at 1000 mV·s–1) and specific capacitance values (325 F·cm–3) compared with the pristine aqueous electrolyte, with the advantage of superior energy density (16.3 versus 8.7 mWh·cm–3) due to a noticeably enlarged potential window in [Pyr+][HSO4–]–water binary mixtures.

You may read the full paper here.

Scientific publication

The effects of local graphitization on the charging mechanisms of microporous carbon supercapacitor electrodes

/in , , /by

Authors: Huan Yin, Hui Shao, Barbara Daffos, Pierre-Louis Taberna, Patrice Simon.
Journal: Electrochemistry Communications (2022)

 

Abstract

The electrochemical quartz crystal microbalance (EQCM) technique has been used to study the charge mechanisms in two TiC-derived nanoporous carbons (CDC), synthesized at 800℃ and 1100℃. These two carbons have a similar pore size and porous volume, but the CDC prepared at 1100°C shows a more graphitic microstructure. The EQCM study revealed that the charge storage mechanism in the CDC-800 is mainly controlled by a counter-ion adsorption process, while an expanded ion-exchange process was observed for the CDC-1100. Combined with the potential of zero charge (PZC), these measurements suggest a strong interaction between the anions and graphitic carbon. For the first time, we provide experimental evidence that the local carbon structure affects the charge storage mechanism of the electrical double-layer capacitance in high surface area porous carbons.

graphitization graphical abstract

 

You may read the full paper here.

Scientific publication

Electropolymerization of thiazole derivatives bearing thiophene and selenophene and the potential application in capacitors

/in , , /by

Authors: Seongjun Hong, Joon Ho Yoon, Seunghyun Jeong, Yang-Rae Kim and In Tae Kim.
Journal: Journal of Electroanalytical Chemistry (2022)

 

Abstract

Three thiazole derivatives bearing thiophene and selenophene are synthesized and used as monomers for electropolymerization. The electropolymerization process is studied using cyclic voltammetry (CV) and electrochemical quartz crystal microbalance (EQCM) techniques. Deep understanding is obtained regarding the pseudocapacitor performance of deposited polymer layers by subjecting the macroelectrode and ultramicroelectrode to CV and galvanostatic charging–discharging experiments in three kinds of electrolytes. Notably, the highest specific capacitance is observed in the derivative bearing selenopheno[3,4-d]thiazole and selenophene in a solution of tetrabutylammonium tetrafluoroborate. Furthermore, the electropolymerization rate is influenced by the kind of chalcogenophene and the CV scan rate. A spectroelectrochemistry experiment reveals the optical and electrochromic behavior of the deposited polymer layers. From these results, the pseudocapacitor performance of the deposited polymer layers is related to anion intercalation/deintercalation processes by faradaic reactions of oligomer chains. The EQCM experiments also reveal these processes during electropolymerization and anion intercalation/deintercalation into the deposited polymer layers. Finally, the approximate molecular weight of the solvated anion and the number of solvent molecules surrounding a solvated anion are analyzed using the EQCM data.

 

You may read the full paper here.

Publication on AWSensors technology

Interfacial charge storage mechanisms of composite electrodes based on poly(ortho-phenylenediamine)/carbon nanotubes via advanced electrogravimetry

/in , , /by

Authors: El Mahdi Halim, Rezan Demir-Cakan, Hubert Perrot, Mama El Rhazi, Ozlem Sel

Journal: The Journal of Chemical Physics (2022)

 

Abstract

To reach a deeper understanding of the charge storage mechanisms of electrode materials is one of the challenges toward improving their energy storage performance. Herein, we investigate the interfacial ion exchange of a composite electrode made of carbon nanotube/poly( ortho-phenylenediamine) (CNT/P oPD) in a 1M NaCl aqueous electrolyte via advanced electrogravimetric analyses based on electrochemical quartz crystal microbalance (EQCM). Classical EQCM at different scan rates of the potential revealed the complex electrogravimetric behavior likely due to multi-species participation at different temporal scales. Thereafter, in order to better understand the behavior of each species (ions, counter ions, and co-ions) in the charge compensation mechanism, the electrogravimetric impedance spectroscopy analysis (also called ac-electrogravimetry) was pursued. Ac-electrogravimetry revealed the role of each species where Na + cations and Cl − anions as well as protons participate in the charge compensation mechanism of the CNT/P oPD composite with different kinetics and proportions. The water molecules with opposite flux direction with the cations are also detected, suggesting their exclusion during cationic species transfer. Having analyzed ac-electrogravimetry responses in depth, the synergistic interaction between the CNT and P oPD is highlighted, revealing the improved accessibility of species to new sites in the composite.

 

You may read the full paper here.

Scientific publication

Interface evolution and performance degradation in LiCoO2 composite battery electrodes monitored by advanced EQCM

/in , , /by

Authors: Wanli Gao, Christel Laberty-Robert, Natacha Krins, Catherine Debiemme-Chouvya, Hubert Perrot and Ozlem Sel.
Journal: Electrochimica Acta (2022)

 

Abstract

Unravelling the underlying reasons for degradation mechanism of battery materials is of great fundamental and practical importance. For a classical electrode consisting of an active material, a conductive additive, and a polymeric binder, its capacity fading is commonly related with (i) mechanical degradation of polymeric binder and/or (ii) structural and compositional degradation of active materials. The former is more relevant for electrodes showing volume expansion and represented by the progressive breakage of polymeric binder network during battery operation, leading to the dissolution of the other two components into electrolytes. The latter is generally reflected by an irreversible phase transition in active materials, which may affect the species exchanged at the electrode/electrolyte interface and their interfacial transfer dynamics. By employing a coupled methodology pairing electrochemical techniques with piezoelectric probes derived from quartz crystal microbalance (QCM), this work reports on the evolution of the interfacial processes during electrochemical cycling and correlates to the performance degradation of the electrodes. Shown on a LiCoO2 (LCO) composite electrode as a model system, it was revealed that bare Li+ without a hydration sheath plays a dominant role in charge balance irrespective of the aging degree of the electrode under the experimental conditions of this work. However, Li+ transfer is closely accompanied with free H2O molecules with a Li+:H2O ratio around 10:1 at a polarization state close to LCO redox potential (0.65 V vs. Ag/AgCl). This ratio persists in all cycled electrodes with gradually faded interfacial transfer kinetics of Li+ and H2O along cycling. Such a fading in species interfacial transfer kinetics driven by the surficial evolution from LiCoO2 to CoO plays a major role in the electrode performance degradation during cycling.

LiCoO2 composite battery electrodes

You may read the full paper here.

Scientific publication

Ion Dynamics at the Carbon Electrode/Electrolyte Interface: Influence of Carbon Nanotubes Types

/in , , /by

Authors: Freddy Escobar-Teran, Hubert Perrot and Ozlem Sel.
Journal: Materials (2022)

 

Abstract

Electrochemical quartz crystal microbalance (EQCM) and AC-electrogravimetry methods were employed to study ion dynamics in carbon nanotube base electrodes in NaCl aqueous electrolyte. Two types of carbon nanotubes, Double Wall Carbon Nanotube (DWCNT) and Multi Wall Carbon Nanotube (MWCNT), were chosen due to their variable morphology of pores and structure properties. The effect of pore morphology/structure on the capacitive charge storage mechanisms demonstrated that DWCNT base electrodes are the best candidates for energy storage applications in terms of current variation and specific surface area. Furthermore, the mass change obtained via EQCM showed that DWCNT films is 1.5 times greater than MWCNT films in the same potential range. In this way, the permselectivity of DWCNT films showed cation exchange preference at cathode potentials while MWCNT films showed anion exchange preference at anode potentials. The relative concentration obtained from AC-electrogravimetry confirm that DWCNT base electrodes are the best candidates for charge storage capacity electrodes, since they can accommodate higher concentration of charged species than MWCNT base electrodes.

You may read the full paper here.

Scientific publication

Synthesis and covalent immobilization of redox-active metallopolymers for organic phase electrochemistry

/in , , /by

Authors: Hanna Hübner, Riccardo Candeago, Deborah Schmitt, Alexander Schießer, Beichen Xiong, Markus Gallei and Xiao Su.
Journal: Polymer (2022) 244, 124656.

 

Abstract

Redox-active metallopolymers are promising stimuli-responsive platforms for a range of applications including sensing, energy storage, and selective separations. In particular, heterogeneously-functionalized metallopolymers can modulate the capture and release of target molecules, driven by redox electron-transfer. However, prior metallopolymer-functionalized electrodes have been fabricated by non-covalent methods, and tailored for aqueous phase applications. As such, despite the existing potential for heterogeneous applications in organic phase, there are significant constraints to the stability of metallopolymers in organic solvents, including high solubility in solvents such as chloroform or tetrahydrofuran. We propose the immobilization of thiol-functionalized redox-active metallopolymers on metallic surfaces as a facile way to enhance stability and cyclability in organic media, and thus broaden the applicability of redox-metallopolymers for organic phase applications. We explore the anionic polymerization of metal-containing monomers vinylferrocene (VFc) and ferrocenyldimethylsilane (FS), and their thiol end-functionalization by living anionic polymerization strategies. PFS and PVFc with molar masses ranging from 1800 to 49900 g mol−1 and 2900 to 6300 g mol−1 respectively were prepared with a segment of poly(ethylene sulfide), as characterized by size-exclusion chromatography, NMR spectroscopy, MALDI/ToF, thermogravimetry, and elemental analysis. Both metallopolymers were immobilized on gold substrates by a grafting-to protocol, with demonstrated redox-responsiveness by electrochemical control. In the case of immobilized PVFc, operando electrochemical testing demonstrated the stable and reversible electrochemical cycling capabilities (>74% maximum current retained after 100 oxidation/reduction cycles) in several organic solvents including chloroform, tetrahydrofuran, ethanol, methanol, acetonitrile, and acetone. Immobilized PFS was stable in chloroform, with a 83% maximum current retained after 100 oxidation/reduction cycles. We envision future applications of these covalently immobilized metallopolymers for a broad range of fields from selective separations to sensing and energy storage.

 

You may read the full paper here.

Publication on AWSensors technology

Correlation between the interfacial ion dynamics and charge storage properties of poly(ortho-phenylenediamine) electrodes exhibiting high cycling stability

/in , , /by

Authors: El Mahdi Halim, Rezan Demir-Cakan, Hubert Perrot, Mama El Rhazi, Ozlem Sel

Journal: The Journal of Power Sources (2019)

 

Abstract

An integrated electrogravimetric study based on electrochemical quartz crystal microbalance (EQCM) unravels the interfacial ion transfer phenomena of the poly(ortho-phenylenediamine) (PoPD) thin film electrodes. Through a methodology coupling QCM with electrochemical impedance spectroscopy (ac-electrogravimetry), our work indicates that charge compensation process of PoPD in aqueous electrolytes (in acidified NaCl) occurs with the participation of multiple species, each playing a role at different temporal scales. The PoPD films are tested in a 2 electrode Swagelok cell in which Zn is used as both reference and counter electrodes and exhibit excellent stability over 8000 cycles with a relatively high specific capacitance of about 110 F g−1 at 30 C (0.63 mA cm−2) current density. The high rate capability and the excellent cycling stability of the PoPD electrodes are correlated to the electrolyte composition and the significant role of H+ to the charge compensation process is unravelled, which is made possible with coupled electrogravimetric methods of our study. By determining the interfacial flux dynamics and as well as the relative proportions of species transferred at the electrode/electrolyte interface, our results contribute to the understanding of the charge-discharge process of PoPD polymer, yet underexplored but emerging as a pseudo-capacitive electrode material.

You may read the full paper here.